Показано с 1 по 4 из 4

Тема: incubusCamd

  1. #1
    Member
    Регистрация
    17.05.2008
    Сообщений
    95

    incubusCamd

    Появился новый эмулятор для 9000/900 и Катрейна!
    Сам пока не проверял!
    http://depositfiles.com/files/89vlamrha

  2. #2
    Member
    Регистрация
    17.05.2008
    Сообщений
    95

    Re: incubusCamd_0.5

    incubusCamd-0.50-newcs-1.62

    http://depositfiles.com/files/8ldyg8kpl

  3. #3
    Member
    Регистрация
    29.08.2008
    Сообщений
    32

    Re: incubusCamd

    Вот только бы знать как его настраивать

  4. #4
    Member
    Регистрация
    17.05.2008
    Сообщений
    95

    Re: incubusCamd

    /var/bin/incubusCamd.conf

    ################################################## ############################
    # incubusCamd configuration file #
    # All configuration options in this file observe the same format: #
    # <configuration_name>=<configuration_value> #
    # #
    # Each section are [<section_name>:<option_1>:<option_x>] like. #
    # #
    # No matter about white spaces on any place or UNIX/DOS style files #
    ################################################## ############################

    ########################### general configuration ############################
    [General]
    # Enable or disable background execution of the cam
    # 0 - Disable
    # 1 - Enable
    background_execution=1

    # First release don't use this, you can delete it
    # Used to set the priority where first try to get the current Ecm's DW
    # divide each option by comma, options are card protocol name or "emu" (for the internal emulator)
    # mode=emu,cccam,gbox,camdX,newcamd,radegast,aroureo s

    ############################ caid configuration ##############################
    #
    # First of all the cam use the incubusCamd.prio file, then use the
    # configuration below.
    # Sections are defined by the value of the CaID.
    # You can choose the default ecm table used by the codify, this means that
    # you can choose the first byte of the raw ecm that is downloaded from sat.
    # If you don't know what value to insert, use "80". (all value are in hex)
    # Default value for ecm_table is 0x80.
    # The option "priority" tells if one caid should be selected before try
    # another one with a priority value greater.
    # The less is the value the greatest is the priority. Choose from "0" to any value,
    # priority value is decimal.
    #
    [CaID:0100]
    ecm_table=80
    priority=1

    [CaID:0500]
    ecm_table=80
    priority=1

    [CaID:0600]
    ecm_table=80
    priority=1

    [CaID:0919]
    ecm_table=80
    priority=1

    [CaID:093B]
    ecm_table=80
    priority=1

    [CaID:0B00]
    ecm_table=80
    priority=1

    [CaID:0D00]
    ecm_table=80
    priority=1

    [CaID:1700]
    ecm_table=80
    priority=1

    [CaID:1800]
    ecm_table=80
    priority=1

    [CaID:2600]
    ecm_table=80
    priority=1

    ########################### provider configuration ###########################
    #
    # All parameters are in hexadecimal notation.
    # Each section is defined by the provider id value.
    # If you don't know the provider id value then use the provider id "FF00".
    # On provider FF00 goes all provider wich are not declared. If the provider
    # is declared then the cam will use the provider founded.
    #

    [Prov:0501]
    # ----------------------------------------------------------------------------
    # URL of card-server to use, formats are as follows:
    #
    # newcamd://<username>:<password>@<hostname>:<port>/<des_key>
    # aroureos://@<hostname>:<port>
    # radegast://@<hostname>:<port>
    #
    # Example:
    # newcamd://foo:bar@192.168.0.100:12345/0CE3476FF2E1C9D9A0A109B371E3
    #
    # Multiple card-server url's can be specified for server fail-over.
    # If the emu fails to connect or fails to get valid CW's, it will try to
    # connect to other servers in a round-robin fashion.
    #
    # Up to 16 servers can be added from index 0 to 15.
    #
    # You can choose also to select a cccam or gbox server, but they must be declared
    # in the "servers configuration" section ( [Servers] ).
    # e.g. : if you want to use a cccam server for a provider you must put it on
    # the parameter card_server_url_0=cccam://
    # NO MATTER the value after the double slash because server configuration is
    # made in the section [Servers].
    # Only for newcamd, radegast and aroureos is usefull to put correct connection
    # parameters because they are provider dependent.
    #
    #

    [Prov:FF00]
    # this provider is a stand-in for all providers not declared------------------
    #
    # For example i choose to use gbox protocol on all other provider.
    #
    card_server_url_0=cccam://<username>:<password>@<hostname>:<port>

    ########################### servers configuration ############################
    #
    # This is the section for the multi-server configuration.
    # First release use this only to connect on ONE cccam server and on ONE gbox
    # server.
    # gbox://<localhost>:<localport>:<password>@<peer_address>: <peer_port>:<peer_pass>

    [Servers]
    card_server_url_0=cccam://<username>:<password>@<hostname>:<port>
    #card_server_url_1=gbox://<localhost>:<localport>:<password>@<peer_address>: <peer_port>:<peer_pass>

Ваши права

  • Вы не можете создавать новые темы
  • Вы не можете отвечать в темах
  • Вы не можете прикреплять вложения
  • Вы не можете редактировать свои сообщения
  •